English English Nederlands Nederlands Deutsch Deutsch Italiano Italiano Español Español Français Français 简体中文 简体中文 Português Português Русский Русский
    DetailingWiki Newsletter
    Get free and automatic updates on new articles
    We respect your privacy. No data is used for anything other than sending the newsletter!

    Advertisement

Troubleshooting – Dual Action polishing

Written by:

Listed here are some typical problems associated with dual action polishing, with causes and possible solutions to try. If you are having problems achieving the correction you expect, or getting a polish to finish down, here’s where to look. This is a very generic troubleshooting guide to help you solve some problems you may encounter.

Problem

Correction not at the desired level, swirls and scratches remain.
Possible causes:

  1. Polish and pad combination too light for paint and defects
  2. Polish not being worked to its full potential
  3. Work area too large
  4. Marks to deep to remove by machine polishing
  5. Defects below top layer of paint

Solutions

  1. Step up to a more aggressive polish and pad combo and repeat polishing. Keep steeping up abrasive level until desired correction is achieved*
  2. Ensure polish is being fully worked – residue should go clear and for many polishes vanish and start to dust slightly. Takes a good 2 – 5 minutes depending on polish being used**
  3. Reduce work area to no more than 18″ square, but ideally 12″ square or even smaller on hard paints or hot days where polish can dry out quickly
  4. Any mark which catches the finger nail will be very hard to fully remove by machine polishing. Wet sanding is an option for severe RDS, but even this wont solve an iddue of a deep scratch which will need painting and flatting to fully repair.
  5. On rare occasions, defects can be flashed in below the clearcoat (typically only if car has been poorly resprayed). It is not possible to reach these marks without removing the clearcoat – respray required to fix.

* Exercise caution as abrasive polishes remove small amounts of paint, the amount of which increases with aggression of pad and polish. Ideally check the thickness of the paint before using aggressive compounds.

** Problems with fully working a polish can arise from a few things – see below.

Problem

Polish dries out and appears to be worked too fast (under a minute).
Possible causes:

  1. Too little polish used
  2. Too large an area worked at any one time
  3. Machine speed too high
  4. Panel or ambient temperature too high

Solutions

  1. While only a small amount of polish is required (a couple of beads per section, sometimes a little more), initial passes require a little more polish to prime the pad. Too little will result in it drying out too quickly and not properly working.
  2. Large work areas allow polish to dry out before it has had a chance to fully work, reducing the work time and the level of correction and quality of finish achieved. Reduce to 12″ square or less on hot days.
  3. While many polishes are happy to be worked at speed 5.5 to 6 on typical DA polishers, others need to be worked at slower speeds (5 or below). If the polish appears to be drying out quickly, consider reducing the machine speed.
  4. High ambient or panel temperatures can dry out polishes before they have fully broken down. Always try to avoid direct sunlight and high temperatures, the ideal is to be working inside. Where this is not possible, reducing the work area and machine speeds can help prevent the polish from drying out too quickly. A spritz of water or quick detailer can also help but be careful this does not adversely affect the polish lubricants.

Different related articles

  • Carpro
    Manufacturers
    Carpro is a brand of detailing products that aims at using the latest technologies to create the best products. The brand originates from South Korea and is led by Avi. Carpro's full name is Carpro Trading Ltd....
  • Polishing rear softtop window
    Correction
    Polishing the rear softtop window of a convertible is not overly difficult, but might require a bit of trial to get the technique right. There are a few ways to handle this....
  • What is paint repair
    Correction
    Paint can be repaired in several different ways. Polishing is very popular one amongst detailers, but not the only one. Some forms of paint repair are: respray, spot-repair and filling in chips. The need for what form of repair often depends on the size of the damage and/or the location....
  • How to polish metal
    Correction
    As with most products, it helps to know how to polish metal. In many cases you can only give a general guide, because even though some products can fall in the same catgory, they might still need a slightly different way of applying. Metal polish is one of those products....
  • How to restore oxidized paint
    Correction
    Paintwork can, in some cases, become oxidized. Making it turn matte and slightly fade color. If untreated, it can eventually cause the lacquer and/or paintwork to completely fail. It is most common on red cars, but it can happen with every color....
  • The best coating
    Detailing Miscellaneous
    It is often asked on detailing fora and social media: "what is the best coating". Off course there is a difference between certain products and brands, but it is important to know what you are asking. In this guide I will try to explain what the problem is with this question unless it is asked more in-depth....

Links to this article

There are no external links to this article. Yet.
Sidebar



Stay up to date with our free newsletter
Always be the first to know about new updates, articles and other informative content.
Don't miss out, opt in!
We respect your privacy. No data is used for anything other than sending the newsletter!